Kennedy Series with Lacquered 100% Solid Maple Hardwood 1 3/4" Thick Top - Square Cut Edge

As low as $290 Regular Price $290

SKU

KWL

Skip to the beginning of the images gallery

Meet ANSI, BIFMA, DIN and GSA Structural Standards.
6,600 Lbs. Capacity Apron (Strong Cold Rolled Steel).
25-Year Unconditional Warranty.
Fast and Easy Assembly.
Factory Assembly Available.
Save Over 60% On Shipping With This Model.
1-3/4" Thick Top.
Bench Frame Steel 16-gauge.
Butcherblock Grading.
Available 24”, 30”, 36”, 48” Deep and Custom.

Preferred for its hard surface, beauty and durability, the Solid Maple Butcherblock used by BenchPro™ is made from 1-3/4 thick strips of genuine Maple Hardwood. To prevent warpage and splitting, the wood is dried in a low-heat atmosphere for almost one year before it is cut into strips and glued edge to edge. The hardwood strips vary in width so that some strips are single and some strips are double wide. This gives the tops added strength while reducing the possibility of the top splitting along its seams.

Our stock over 500 Maple Butcherblock tops is sufficient to cover most larger orders. We receive unfinished tops in truckload quantities direct from the mill. We first size and sand them, then round the edges, and then finish them in either an oiled or lacquered finish. (While lacquer finished tops have a nicer appearance for offices, the less expensive oiled finish is generally best for production and high use areas, as they can be resurfaced easily.
Most of our competitors use Ash, Alder, or combinations of other less expensive woods depending on the market price. Some don't round the edges or finish the ends.

! The longer the table, the weaker the table. To counter this, our eight foot long benches have 66% more steel in the understructure while ten foot long benches have 207% more steel there. These longer tables, even reinforced to this extent, will show some minor deflection in the center due to gravity.

Workbench Warranty

PRINT

Workbench Warranty

BenchPro™ has been producing the nation's strongest, longest lasting ergonomic workbenches since 1987. We are so sure our products will perform properly, we offer the following warranty:

BenchPro™ benches, options and accessories are warranted to the original purchaser for 25 - years. This includes every component and every function.

Exceptions:

Polk and Eisenhower series are warranted for ten years.

Workbenches used in multiple shift operations shall have the warranty prorated accordingly.

Hydraulic bench lift - system components are warranted for ten - years.

All lighting products are warranted for ten - years.

For Service: Call BenchPro™ at 888-700-9888 or email info@benchpro.com. Customers only have the obligation to report the problem and BenchPro™ will take care of the rest.

BenchPro™ will either refund the entire purchase price including freight and tax (if any) or replace the product or component that is defective, and pay for the freight.

Product Returns:

As we make all orders from base materials, we charge a "restocking charge" on unneeded products. We also charge a restocking charge for products ordered but cancelled after the product is built. This is to cover our repackaging and handling. Customers pay the cost of return freight.

Restocking charge schedule:

A. Kennedy, Roosevelt Series in standard sizes and colors will be charged 10%.
B. Any bench in a custom size or color will be charged a 50% restocking charge, as we will have a difficult time reselling them.
C. Chemical Resistant tops will be charged an additional 10% restocking charge, above those listed above.
D. Custom and non-catalogue items are non-returnable.
E. No product shall be returned after 90 days.

No return of defective product is ever required. (We may ask for an electronic photo in cases where we have not seen the problem before).

From the lawyers: In no case shall BenchPro™, its distributors, employees, related divisions, and other entities be responsible for any direct, consequential or indirect damage caused by the use, inability to use, or incorrect use of our products. Our liability shall be limited to replacement of product or a full refund.

Due Diligence: Please, if a chair or workbench is found to be defective in a way that could lead to an accident, take it out of service and tag it as dangerous until replacements or replacement parts are received and assembled. Dangerous products should not be put into open waste disposal systems until they have been made unusable, so that no third party can reclaim them and be injured.

Integrity Testing

Test	Basis	Description	Pass	Media
Horizontal Static Load Test. BSI EN 13150:2001 A.3.1	Evaluate the ability of the workbench to withstand fatigue stress and wear caused by horizontal forces on the workbench top.	72.5 Psi is applied ten times at the center of each edge. The feet are securely attached to the floor and a verified distance of inflection is observed. To pass the test, the components of the bench are inspected and verified to have full integrity and no reduction in functionality.		Photo Video Technical Data
Vertical Static Load Test. BSI EN 13150:2001 A.3.2	Evaluate the ability of the workbench to withstand fatigue stresses caused by a vertical impact.	105 PSI is applied with a downward force 10 times on each edge. Following the test, the bench is inspected for warping or damage. No changes were found.		Photo Video Technical Data
Sustained Vertical Load Test. BSI EN 13150:2001 A 3.3	Evaluate the ability of the workbench to withstand a load for 24 hours.	1.25 kg / sqm (275 lbs / sqin) is uniformly loaded into the surface of the workbench. 24 hours pass. Eight points are measured to ground before loading, after loading and once the load is removed to determine if there is any inflection of the workbench. The bench is inspected for damage following the test as well. The Kennedy Series is rated to hold up to 5,500 lbs on the surface. This weight had no impact on performance of the bench.		Photo Video Technical Data
Horizontal Impact Stability Test of Free Standing Workbenches. BSI EN 13150:2001 A 3.5	Verify the ability of a workbench to withstand a repeated impact from people walking into it.	A basketball that is filled to 72.5 psi is attached to a weight and dropped from a standard distance to simulate the impact of a person walking into the table with 110 psi. The impact is repeated and the table is inspected for damage. No damage occurred.		Photo Video Technical Data
Drop Test of movable workbenches (tables). BSI EN 13150:2001 A 3.7	The purpose of this test is to check the strength and functionality of the casters after being tested in free fall strike the floor.	The workbench is dropped from a height of approximately 6" ten times on each end. The casters are tested in the locked position. Following the test, it was verified that the bench maintained full and smooth motion of the wheels.		Photo Video Technical Data
Horizontal Fatigue Test. BSI EN 13150:2001 B.3	Verify the ability of the workbench to withstand multiple side impacts.	72.5 PSI are applied 30,000 times to each end while 110 lb. weighs the top of the table down. Following the test, the bench is inspected for damage and none was found.		Photo Video Technical Data
Vertical Fatigue Test. BSI EN 13150:2001 B.4	Evaluate the ability of the workbenches to withstand fatigue stresses and wear caused by vertical forces on the workbench top.	110 PSI is applied at the middle of the long edge in a downward direction. This is repeated 20,000 times on each edge. Following the test, the bench is inspected for signs of fatigue. No fatigue occurred.		Photo Video Technical Data
Vertical Impact Test. BSI EN 13150:2001 B.5	The purpose of this test is to check the strength and functionality of the workbench.	55 lb is dropped onto the middle of each edge from 6 in, 8 in and one foot. Following the test, the bench is inspected for structural damage. The bench was not affected.		Photo Video Technical Data
BenchPro™ Pull Test	Verfies the ability of the workbench frame to endure a large force from the side.	The bench is secured to the ground and the top is pulled laterally at 450 psi until the bench has shifted 1 inch toward the force. Following this, the bench is inspected for damage and none was found.		Photo Video Technical Data

BSI: British Standard for Industry, the industry standard for workbenches.

Ease of Assembly

Kennedy Series Bench Assembly.

1. Place your new Benchpro™ workbench on top of a table with the cardboard seam facing up. Open the carton. don't remove the cardboard yet.

2. Position the legs. If you have a lot of benches to do, we recommend two man teams. If you have Static Control benches, make certain the wrist strap jack is on the front side of the leg.

3. Insert a bolt with a lock washer into each leg.

4. Tighten until lock washer is flat. It doesn't have to be tighter than that.

5. If you ordered drawers or CPU holder, assemble them next. (See instructions below)

6. Turn it over. You're done!

Popular Accessories

View All Accessories
	Drawers These fully-welded drawers hold up 100 lbs.
	Shelves Choose from upright-mounted, riser or under-shelves.
	Lights Add fluorescent or LED lights above your workbench.
	Uprights Add shelves lights or accessories above your workbench.
	Power Strips Add UL listed power strips to your workbench.
	Bin Rails Add convenient bin access to your workbench.
	Casters Make your workbench mobile with these non-marring casters.
	Articulating Accessories Choose from Monitor, Bin Box, Document and Tool Holders.